Dixon 5501 Manual do Utilizador

SEAT ASSEMBLY INSTRUCTIONS 1. Place seat back against frame of seat bottom. Align top & bottom holes in frame with the t-nuts in seat back. Inse

12. Install all-thread hex head bolts into seat straps. Place (1) 5/16-18 x 3" bolt through hole located 1 -5/8" from end of strap. Place

UPPER CONTROL LEVER INSTALLATION 1. Raise rear body cover to fully open position. 2. Install flat washer on right hand swivel plate weldment. Next i

MOWER DECK INSTALLATION NOTE: Brake link (P/N 5283) normally used for installation of engine to mower deck drive belt, has been placed in position d

MOWER DECK LEVELING PROCEDURE LEVELING PRINCIPALS: A. There are a total of (4) threaded adjusters which will control the attitude or pitch of the mo

FINAL PREPARATION MOWER DECK DEFLECTOR: Remove hair pin cotter (P/N 3072) from deflector pin (P/N 6402), remove pin. Position deflector (P/N 9264) on

OPERATION INSTRUCTIONS The safe and successful operation of the Model 5501 will depend upon the operator having the correct knowledge of all controls

OPERATION INSTRUCTIONS: (Continued) BRAKING: To brake mower, move both levers in direction opposite of travel, release levers to neutral, set pa

CARE AND MAINTENANCE - MODEL 5501 This portion of the Model 5501 owners manual deals with normal service items which can be performed by the owner. P

PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Dixon has used two types of electric clutches. One type is the Borg Warner and the second one is the Ogura.

IMPORTANT - READ CAREFULLY The Dixon ZTR Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is

CARE AND MAINTENANCE - MODEL 5501 MOWER DECK SERVICE CUTTER BLADE REMOVAL - BELT TENSION: "CAUTION" The removal of the cutter blades for ei

CARE AND MAINTENANCE - MODEL 5501 DRIVE SYSTEM ADJUSTMENTS: Adjustment of the drive system is limited to the actual function of the hydrostatic tran

ADJUSTMENT POINTS FOR T-BOX BELT TENSION Page 19

FORWARD LEVER STOP ADJUSTMENT Page 20

CARE AND MAINTENANCE - MODEL 5501 LUBRICATION CHASSIS AND MOWER DECK: Number of grease zerks used: (7) LOCATIONS: (1) each front wheel caster, front

CARE AND MAINTENANCE - MODEL 5501 CLEANING THE MOWER: A clean machine is a source of pride to the owner. However, cleaning by use of high pressure co

TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any multi-blade mower. Type and conditions of grass, c

TROUBLESHOOTING DRIVE SYSTEM: SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Adjust per operators manual Consult yo

TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consult

Page 26

INDEX 1. SAFETY ... Pages 1- 3 2. WARRANTY POLICY ...

Page 27

Page 28

Page 29

Page 30

Page 31

Page 32

ZTR 5501 PARTS LIST 1300 Drive Belt 3100 7/16" HD Flat Washer 1384 Tank Mount Bracket (Short) 3106 1/4"X1"Spirol Pin 1385 Tank Mou

ZTR 5501 PARTS LIST 3318 3/8"-16X2 1/4" HH Bolt GR8 3655 Floor Pad Left Rear 3319 Idler Shock Mount 3656 Floor Pad Right Rear 3321 5/16&

ZTR 5501 PARTS LIST 4256 Utility Box 5565 Oil Filter 4274 Choke Cable 5585 Tab 4276 Headlight Assembly 5595 Hose 5/8" X 14" 4384 Rel

ZTR 5501 PARTS LIST 8439 E-Ring 9212 Spring (Belt Tensioner) 8440 Ball 3/8" Diameter 9219 Deck Hub 8441 Bolt 1/2"-20 X 2 1/2" 922

SAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY The following examples are the most common causes of injury to the operato

NOTES Page 37

NOTES Page 38

DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYYILLE KS 67337 O945 316 251 2QOO FAX 316 251 4117

SAFETY SAFETY REMINDERS: READ CAREFULLY BEFORE OPERATION 1. Wear appropriate, safe clothing when mowing - close fitting jeans or slacks and heavy le

SAFETY REMINDERS: (Continued) 14. Never lift lawnmower by the body, lift only by the frame. 15. Never carry passengers. 16. Use care when pulling

DIXON LIMITED WARRANTY POLICY - HYDRO-GEAR MODELS This warranty policy applies to all Hydro-Gear mowers or any 50" model, purchased on or after

SPECIFICATIONS CHASSIS: 11 GA - rectangular tube. BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for ba

Page 6 SET UP AND SERVICE 1. Seat Assembly Instructions 2. Upper Control Lever Installation 3. Mower Deck Installation 4. Deck Leveling 5. Final